(0,50mm) .0197" (0,80mm) .0315" hqcd, eqcd series www.samtec.com specifications for complete speci cations see www.samtec.com? hqcd or www.samtec.com?eqcd cable: 38 awg micro ribbon coax cable signal routing: 50 single-ended overall length: (95,3mm) 03.75" to (1m) 40" standard cable flexing life: >10,000 cycles cable bending radius: <2,5mm plating: au over 50? (1,27?) ni current rating: 300 milliamp max cable propagation delay: 4.4 nsec/meter operating temp range: -40? to +105? unmating force (-rt1 option): -rt1 option increases unmating force up to 50% rohs compliant: ye s no. of positions per row wire length ??xx.xx? = wire length in inches (95,3mm) 03.75" minimum type hqcd = (0,50mm) .0197" pitch eqcd = (0,80mm) .0315" pitch ?030, ?060, ?090, ?120 (hqcd series) ?020, ?040, ?060, ?080 (eqcd series) application specific ? other sizes and lengths ?other terminations ? other wire awg contact dr@samtec.com end to end l (24,13) .950 (21,21) .835 (20,47) .806 (18,29) .720 (17,55) .691 (16,81) .662 surface mount to surface mount surface mount to edge mount (terminal) surface mount to edge mount (socket) edge mount (terminal) to edge mount (terminal) edge mount (terminal) to edge mount (socket) edge mount (socket) to edge mount (socket) hqcd mates with: qth, qsh eqcd mates with: qte, qse wire length (1,27) .050 oal = wire length + l #4-40 thread end no. 1 (?tl shown) end no. 2 (?eu shown) applications processing conditions will affect mated height. (9,28) .365 (16,56) .652 (12,70) .500 note: cable lengths longer than 40.00" (1 meter) are not supported with s.i. test data. note: verify part number with samtec s interactive cable builder at www.samtec.com/ cable_builder/pitch.asp note: this series is non-standard, non-returnable. screw mount applications (?f, ?s, ?b) file no. e111594 f-210 rated @ -3db insertion loss cable length 39.37" (1m) eqcd 465 mhz / .930 gbps hqcd 370 mhz / .740 gbps performance and complete test data available at www.samtec.com?eqcd, www.samtec.com?hqcd or contact sig@samtec.com q strip ? coax cable assemblies ? screw mount options surface mount, edge mount or panel mount 0,50mm or 0,80mm pitch hqcd?030?06.00?ted?ted?1?f eqcd?040?04.00?ttl?str?2 socket or terminal 38 awg micro ribbon coax cable so?0165?04?01?02 so?0318?04?01?02
www.samtec.com end no. 1 end no. 2 specify end assemblies from chart wiring option ?1 = pin 1 to pin 1 ?2 = pin 1 to pin 2 ?3 = pin 1 to second to last pin ?4 = pin 1 to last pin end options ttr ttl tbr tbl str stl sbr sbl surface mount t erminal, t op mount, notch r ight t erminal, t op mount, notch l eft t erminal, b ottom mount, notch r ight t erminal, b ottom mount, notch l eft s ocket, t op mount, notch r ight, s ocket, t op mount, notch l eft s ocket, b ottom mount, notch r ight s ocket, b ottom mount, notch l eft end 1 or end 2 end 1 or end 2 teu ted seu sed edge mount t erminal, e dge mount, notch u p t erminal, e dge mount, notch d own s ocket, e dge mount, notch u p s ocket, e dge mount, notch d own end 1 only tpu tpd spu spd panel mount (not available on hqcd 120 position and eqcd 80 positions) t erminal, p anel mount, notch u p t erminal, p anel mount, notch d own s ocket, p anel mount, notch u p s ocket, p anel mount, notch d own leave blank for no screw mount & retention end option ?f = screw mount end no. 1 only (n/a with xpx options) ?s = screw mount end no. 2 only ?b = screw mount both ends (n/a with xpx options) (n/a on 80 positions eqcd and 120 position hqcd) ?l = end no. 1 retention pin or socket ?r = end no. 2 retention pin or socket ?d = both ends retention pin or socket ?1 = end no. 1 screw mount. end no. 2 retention pin or socket ?2 = end no. 1 retention pin or socket. end no. 2 screw mount option retention pin applications (?l, ?r, ?d) panel mount end option applications (?tpu, ?tpd, ?spu, spd) retention pin option can increase unmating force up to 50% #4-40 thread panel mount options eqcd?020?40.00?tpd?ttr?1 hqcd?020?06.00?stl?ttr?1?b eqcd?020?06.00?ttl?ttr?1?d
|
